| www.ColoradoClassicBroncos.com http://www.coloradoclassicbroncos.com/ |
|
| Rox Crusher's 77 sport http://www.coloradoclassicbroncos.com/viewtopic.php?f=3&t=120 |
Page 11 of 11 |
| Author: | Rox Crusher [ Thu Jul 01, 2021 4:15 pm ] |
| Post subject: | Re: Rox Crusher's 77 sport |
Last month I replaced the 3-1/2" rear springs with 4-1/2" to eliminate saggy ass syndrome. Turned out pretty good, it raised the rear bumper by 2" (the rear leafs must have had some sag to them). Previously when I had 3-1/2" springs all the way around, my rig had a slight rake to the front which I attributed to the typical settling associated with WH coil springs. So I replaced them with 4-1/2" WH coils thinking they too would settle expecially with the extra weight of the winch........and ultimately the stance would be nuetral. But for some reason the fronts don't seem to have settle while the rears definitely did. |
|
| Author: | Rox Crusher [ Thu Jul 01, 2021 4:33 pm ] |
| Post subject: | Re: Rox Crusher's 77 sport |
Doing some upgrades and maintenance in preparation for the upcoming Rubicon trip ! I have had a small vibration coming from the rear end and the axle keeps leaking at both ends so I replaced the bearings and seals. Looking at the used bearings you could see some slight wear on the races but it also looked like the inner races were rotating on the axles which is worrisome. Ride is much smoother now without any vibration. Hoping the new seals will solve the leaks....... we shall see. Before replacing the wheel bearings, and thinking the vibration was from a worn driveline, I ordered a new one from Tom Woods. I needed a longer one due to the new 4-1/2" springs anyway. Last things on my list include fixing an exhaust leak on driver's side header and installing some new Duff Eibach shocks on the rear if they arrive in time. Other than that I am locked and loaded. |
|
| Author: | Mitche11 [ Mon Jul 05, 2021 9:29 pm ] |
| Post subject: | Re: Rox Crusher's 77 sport |
Great progress Rox. It’s cool to hear about your improvements. I have to replace the bearing and seal on pass rear and I’m a little gun shy because I understand you have to cut the old bearings off. I have a small bearing 9”. Did you cut your bearings off? How’d that go? Thanks! Sent from my iPad using Tapatalk |
|
| Author: | phyler [ Mon Jul 05, 2021 10:21 pm ] |
| Post subject: | Re: Rox Crusher's 77 sport |
| Author: | Mitche11 [ Mon Jul 05, 2021 10:22 pm ] |
| Post subject: | Re: Rox Crusher's 77 sport |
Good idea. Thanks for the insight! Sent from my iPad using Tapatalk |
|
| Author: | Justin [ Thu Jul 08, 2021 5:46 pm ] |
| Post subject: | Re: Rox Crusher's 77 sport |
I've got a press. Usually just cut them most of the way and then hit them with a chisel and big hammer. Happy to help. |
|
| Author: | Mitche11 [ Fri Jul 09, 2021 9:37 pm ] |
| Post subject: | Re: Rox Crusher's 77 sport |
Justin, If I cut mine off, and bring you an axle, bearing, and a 12 pack, do you think we could press mine on? I’d feel better if a bronco guy does it, because we all care a little more. If not, I understand. Sent from my iPad using Tapatalk |
|
| Page 11 of 11 | All times are UTC - 7 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|