| Author |
Message |
|
kbank6
Official CCB Member
Joined: Sun Apr 14, 2013 5:00 pm
Posts: 306
Location: Greeley, CO
|
 D20 clutch and flywheel. I have a new clutch, pressure plate, and flywheel $150.00
Juet pulled it out so there is a little surface rust but it does not have any run time on it.
You do not have the required permissions to view the files attached to this post.
_________________
73 Ranger (Holy Crap, replacing the door post is so much fun!)
|
| Sat Aug 24, 2013 9:16 pm |
|
|
|
Bill K
Official CCB Member
Joined: Sat Sep 08, 2012 7:06 pm
Posts: 30
Location: Boulder Colorado
|
Re: D20 clutch and flywheel. Hi, getting ready to put in an NP 435 tranny once I find a used adapter. Planning on putting in a new clutch at the same time. Don't know about part numbers or names but was wondering if this will work with my 302?
Bill
|
| Sat Aug 24, 2013 10:36 pm |
|
|
|
kbank6
Official CCB Member
Joined: Sun Apr 14, 2013 5:00 pm
Posts: 306
Location: Greeley, CO
|
Re: D20 clutch and flywheel. This came out of a 351W So it has 11" disk, 28oz-164 tooth flywheel.Should have mentioned that...
_________________
73 Ranger (Holy Crap, replacing the door post is so much fun!)
|
| Sun Aug 25, 2013 7:51 am |
|
|
|
Kinder
Official CCB Member
Joined: Wed Sep 29, 2010 10:03 pm
Posts: 4371
Images: 0
Location: Parker, CO
|
Re: D20 clutch and flywheel. Older 351s & 302s use the same setups.
_________________
Best to Date MPG: 26.6
|
| Sun Aug 25, 2013 12:11 pm |
|
|
|
kbank6
Official CCB Member
Joined: Sun Apr 14, 2013 5:00 pm
Posts: 306
Location: Greeley, CO
|
Re: D20 clutch and flywheel. 1983
_________________
73 Ranger (Holy Crap, replacing the door post is so much fun!)
|
| Sun Aug 25, 2013 4:00 pm |
|
|
|
Bill K
Official CCB Member
Joined: Sat Sep 08, 2012 7:06 pm
Posts: 30
Location: Boulder Colorado
|
Re: D20 clutch and flywheel. So it will fit? Maybe fit? Or won't fit? When I get mine out, and if you still have yours, will do a comparison.....
|
| Sun Aug 25, 2013 9:36 pm |
|
|
|
Justin
Official CCB Member
Joined: Sun Oct 10, 2010 12:04 am
Posts: 6198
Images: 0
Location: Lakewood
|
Re: D20 clutch and flywheel. If you've got a 302, very good chance it will fit. If not someone will buy it. Heck, I'd pick it up if the bronco fund hadn't taken a massive beating lately.
|
| Mon Aug 26, 2013 12:05 am |
|
|
|
kbank6
Official CCB Member
Joined: Sun Apr 14, 2013 5:00 pm
Posts: 306
Location: Greeley, CO
|
Re: D20 clutch and flywheel. It should fit but we could match it up.
_________________
73 Ranger (Holy Crap, replacing the door post is so much fun!)
|
| Mon Aug 26, 2013 9:43 pm |
|
|
|
kbank6
Official CCB Member
Joined: Sun Apr 14, 2013 5:00 pm
Posts: 306
Location: Greeley, CO
|
Re: D20 clutch and flywheel. Bump
_________________
73 Ranger (Holy Crap, replacing the door post is so much fun!)
|
| Sun Nov 17, 2013 1:19 pm |
|
|
|
Colorado75bronc
Official CCB Member
Joined: Fri Oct 22, 2010 7:13 pm
Posts: 996
|
Re: D20 clutch and flywheel. All 351w are the same as early 302's so it should fit fine, and should be the 28oz imbalance as only late 302's/ 5.0's are 50 oz imbalance
Sent from my iPhone using
_________________
75' bronco, 302, carb'd for now, i'm gathering parts for efi, 3g alternator, saginaw pump, 4x4x2 box, fw hp44, fw 9", N.P. 435 w/ gearbanger shifter, twin stick'd dana 20, 2" BL, 5.5" wildhorses lift, and 35" km2's
|
| Sun Dec 08, 2013 4:32 pm |
|
|
|
