Pinion Guard Install

[pgilbeau]

I haven't messed with my 9" center section except for putting it in and taking it out. I want to install a Ruff Stuff pinion guard but not sure if I can just pull the bolts and put the guard on or will I need to set the gears back up after pulling the bolts and installing the guard.

https://www.ruffstuffspecialties.com/9F-PIN.html

[Viperwolf1]

No setup required. Might need longer bolts.

[pgilbeau]

No setup required. Might need longer bolts.

Thanks, just wanted to verify beforehand!

[landshark]

confirmed, longer bolts are all that is needed

[pgilbeau]

confirmed, longer bolts are all that is needed

Thanks, time to get started on some stuff.

[Rox Crusher]

I installed the Duff version which is a nice piece

One thing I donΓÇÖt like about any of these is that it makes using the center of the axle as a place to jack the axle up a bit unstable

[pgilbeau]

I installed the Duff version which is a nice piece

One thing I donΓÇÖt like about any of these is that it makes using the center of the axle as a place to jack the axle up a bit unstable

I just checked out the Duff version, seems to add more protection.

[landshark]

Check out the Currie skid/pinion one. Pretty nice.

[pgilbeau]

Check out the Currie skid/pinion one. Pretty nice.

Is this the one? https://www.currieenterprises.com/CE-4303BSP

All I found was ones for the F9 housing.

[landshark]

I think so, its the piece that bolts on. i know it fits the regular currie 9" as someone i know has one installed. To me its way too expensive - $240. The design seems like it would do a great job of protecting the the lip and bottom 3rd member better than anything else out there. Really its super simple and wouldn't be too bad to fabricate. I just decided to weld on some 1/4" plate to the bottom and back of the housing and used the Ruff Stuff Pinion guard.

Screen Shot 2020-10-26 at 10.54.36.png

I

[pgilbeau]

I think so, its the piece that bolts on. i know it fits the regular currie 9" as someone i know has one installed. To me its way too expensive - $240. The design seems like it would do a great job of protecting the the lip and bottom 3rd member better than anything else out there. Really its super simple and wouldn't be too bad to fabricate. I just decided to weld on some 1/4" plate to the bottom and back of the housing and used the Ruff Stuff Pinion guard.

It looks like a nice piece but the $240 is a lot of $. Probably going to go the same route, Ruff Stuff and weld on some plate but not sure yet. The Duff one is tempting but seems like it could possibly catch on stuff.

[landshark]

Agreed - here are a couple of photos of what I did. I dont' have any of the bottom of the housing but its just 1/4" plate similar to the back bottom.

2FD540BB-5E3E-4A02-A39C-DC9652748976.jpeg

B528CBB3-4AB9-4D41-8DE6-A7C1198160A8.jpeg

[pgilbeau]

Thanks for the pic, probably going to do something similar.

[Eck]

Getting prepped to install the ruffstuff pinion guard at some point in the next while and was wondering about the bolt length. I did not order the bolts with the guard (didn't even think about it at that time). Can anyone confirm or recommend the bolts needed? From this thread it looks like longer ones are needed. Would rather get some at ACE than order from RuffStuff.

[landshark]

I don't know the length offhand but you can get them at ACE no problem, thats what i did - assume 1/2" longer grade 8