Going to be finishing off my Edelbrock rebuild tomorrow during lunch and needed a hand with something. Was hoping someone could snap some good hi res pics of the DS and PS linkage and cams. Just want to make sure I get everything back together smoothly.
Thanks.
Edelbrock 1405/1406 assistance needed
-
akaFrankCastle
- Official CCB Member
- Posts: 4901
- Joined: Wed Oct 27, 2010 5:25 pm
Edelbrock 1405/1406 assistance needed
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
-
BNC04
- Official CCB Member
- Posts: 350
- Joined: Thu Jan 27, 2011 12:01 pm
Re: Edelbrock 1405/1406 assistance needed
Once it get light, I can go snap a few pics.
Brett
PM Me if it gets to be 10ish and you dont have them yet. Work may have gotten in the way:)
Brett
PM Me if it gets to be 10ish and you dont have them yet. Work may have gotten in the way:)
75 D44/ARB/Disc PS. 86 5.0 Carbed- NP-435 yukon rear. 4.11 3.5 Susp lift Rampage top
-
Moab Mike
- Official CCB Member
- Posts: 1945
- Joined: Mon Jan 03, 2011 1:59 pm
Re: Edelbrock 1405/1406 assistance needed
o
Last edited by Moab Mike on Wed Apr 13, 2011 2:46 pm, edited 1 time in total.
-
BNC04
- Official CCB Member
- Posts: 350
- Joined: Thu Jan 27, 2011 12:01 pm
Re: Edelbrock 1405/1406 assistance needed
I forgot, I don't have a n electric choke on mine and the manual is not hooked up to anything either
Edelbrock has instructions for most everything here as well.
You can download and blow these up as big as you need
Brett
Edelbrock has instructions for most everything here as well.
You can download and blow these up as big as you need
Brett
75 D44/ARB/Disc PS. 86 5.0 Carbed- NP-435 yukon rear. 4.11 3.5 Susp lift Rampage top
-
akaFrankCastle
- Official CCB Member
- Posts: 4901
- Joined: Wed Oct 27, 2010 5:25 pm
Re: Edelbrock 1405/1406 assistance needed
Brett,
Thanks for the pics. Exactly what I needed. Right now I'm having two problems.
First, the rod indicated below doesn't match up with what I have. Both bends on my rod face the same direction and both ends have the slotted connectors. However, the rod in your picture has opposing bends and appears to use the clip pin to hold the top of the rod in.
The second issue I am having is with the spring indicated in the circle. I need to see where the J bend in this spring is engaged with the linkage.
Thanks for the pics. Exactly what I needed. Right now I'm having two problems.
First, the rod indicated below doesn't match up with what I have. Both bends on my rod face the same direction and both ends have the slotted connectors. However, the rod in your picture has opposing bends and appears to use the clip pin to hold the top of the rod in.
The second issue I am having is with the spring indicated in the circle. I need to see where the J bend in this spring is engaged with the linkage.
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
-
BNC04
- Official CCB Member
- Posts: 350
- Joined: Thu Jan 27, 2011 12:01 pm
Re: Edelbrock 1405/1406 assistance needed
I took a few more closeups.
Keep in mind, this is not my install and I have no idea if it's as it should be normally.
It does run though so something is working but the choke asm is not in use at all.
yes a clip is in place on the top. Sorry, I missed taking a pic of it
Brett
Keep in mind, this is not my install and I have no idea if it's as it should be normally.
It does run though so something is working but the choke asm is not in use at all.
yes a clip is in place on the top. Sorry, I missed taking a pic of it
Brett
75 D44/ARB/Disc PS. 86 5.0 Carbed- NP-435 yukon rear. 4.11 3.5 Susp lift Rampage top
-
akaFrankCastle
- Official CCB Member
- Posts: 4901
- Joined: Wed Oct 27, 2010 5:25 pm
Re: Edelbrock 1405/1406 assistance needed
First, thanks for the pics again Brett. Very helpful
Second, I'm an idiot. One of he things I preach to my guys at work is, "if something isn't working right take a step back and see if it LOOKS right." Well, I should have heeded my own advice.
Turns out I had switched the linkages shown below.
Looks as if the pic didn't update. Anywho, I switched the linkage/rod that physically opens and closes the choke with the one that actuates the rod that passes through the top of the carb.
Second, I'm an idiot. One of he things I preach to my guys at work is, "if something isn't working right take a step back and see if it LOOKS right." Well, I should have heeded my own advice.
Turns out I had switched the linkages shown below.
Looks as if the pic didn't update. Anywho, I switched the linkage/rod that physically opens and closes the choke with the one that actuates the rod that passes through the top of the carb.
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
-
BNC04
- Official CCB Member
- Posts: 350
- Joined: Thu Jan 27, 2011 12:01 pm
Re: Edelbrock 1405/1406 assistance needed
No Problem,, been there done that,, a number of times.
Glad the pics were of some value.
Brett
Glad the pics were of some value.
Brett
75 D44/ARB/Disc PS. 86 5.0 Carbed- NP-435 yukon rear. 4.11 3.5 Susp lift Rampage top