muffler shops, anyone have a good one that they use
- Brianut
- Official CCB Member

- Posts: 350
- Joined: Thu Oct 14, 2010 6:06 am
muffler shops, anyone have a good one that they use
that also isnt too expensive.
I need to extend my tailpipes out from under the truck to help get rid of fumes and my system is rather rusty and I might just replace it. talked to a local Englewood shop and they want $500 to ditch the duals and run a single out the passenger side.
Does that seem reasonable?
Its been along time since I had exhaust done on a truck cant remember what its supposed to cost.
I need to extend my tailpipes out from under the truck to help get rid of fumes and my system is rather rusty and I might just replace it. talked to a local Englewood shop and they want $500 to ditch the duals and run a single out the passenger side.
Does that seem reasonable?
Its been along time since I had exhaust done on a truck cant remember what its supposed to cost.
- Brianut
- Official CCB Member

- Posts: 350
- Joined: Thu Oct 14, 2010 6:06 am
Re: muffler shops, anyone have a good one that they use
looks like I am due for a drive north then, 500 seemed a bit steep or I supose I could see if the guy down here would match the price.
- cpldavis37
- Official CCB Member

- Posts: 357
- Joined: Sun Oct 16, 2011 6:45 pm
Re: muffler shops, anyone have a good one that they use
BDM in Denver did my old f150 for 450. Magniflow mufflers sounded nice.
TJ
"Everyone suspects himself of at least one of the cardinal virtues, and this is mine: I am one of the few honest people I have ever known."
F. Scott Fitzgerald
1974 Ford Bronco 3 1/2 inch James Duff lift ,2 inch body lift, 351w Explorer EFI, Viper built c4, Viper built Dana 20 with wildhorses twin stick, Kinder built Dana 44 with 4.56 gears disc brakes aussie locker and knuckle over conversion, Kinder built 9 inch with grizzly locker 31 spline axles and 4.56 gear
"Everyone suspects himself of at least one of the cardinal virtues, and this is mine: I am one of the few honest people I have ever known."
F. Scott Fitzgerald
1974 Ford Bronco 3 1/2 inch James Duff lift ,2 inch body lift, 351w Explorer EFI, Viper built c4, Viper built Dana 20 with wildhorses twin stick, Kinder built Dana 44 with 4.56 gears disc brakes aussie locker and knuckle over conversion, Kinder built 9 inch with grizzly locker 31 spline axles and 4.56 gear
- airbur
- Official CCB Member

- Posts: 1721
- Joined: Wed Sep 29, 2010 7:39 am
Re: muffler shops, anyone have a good one that they use
AA Performance Muffler & Brakes on Broadway in Littleton. These guys are awesome! I had them install duals. I supplied Hooker Competition Turbo mufflers but they can get anything you want. They had it done a couple hours after dropping it off.
http://local.yahoo.com/info-19565314-aa ... eton%2C+CO
http://local.yahoo.com/info-19565314-aa ... eton%2C+CO
You do not have the required permissions to view the files attached to this post.
Sold: 1970 w/427W Injected Stroker
- Brianut
- Official CCB Member

- Posts: 350
- Joined: Thu Oct 14, 2010 6:06 am
Re: muffler shops, anyone have a good one that they use
zillacon wrote:I had both of mine done for $380 Each from exhaust Pros on Huron. The single exhaust had a magnaflow and the duals has knock off flowmasters with chrome tips. Both were the same price for a cash deal.
was this manifold back or just new muffler the out the back?
- ZOSO
- Moderator

- Posts: 3910
- Joined: Mon Nov 15, 2010 4:58 pm
Re: muffler shops, anyone have a good one that they use
dan I stopped in there yesterday and they quoted 500$ for a single 3" on Steve's half cab.
Rob
74 Ranger EFI351w, 4r70w, ARB 5.13 9in, ARB 5.13D44, and a bunch of other goodies. Best of all the family memories.
04 Mustang Cobra, KenneBell 2.2 feeding a lot of boost on E85. Tire shredding machine
New project: 77 Bronco Ranger, body work and more body work.
Very little left of a 72 durango tan explorer sport
74 Ranger EFI351w, 4r70w, ARB 5.13 9in, ARB 5.13D44, and a bunch of other goodies. Best of all the family memories.
04 Mustang Cobra, KenneBell 2.2 feeding a lot of boost on E85. Tire shredding machine
New project: 77 Bronco Ranger, body work and more body work.
Very little left of a 72 durango tan explorer sport
- Rox Crusher
- Official CCB Member

- Posts: 3980
- Joined: Sun Oct 10, 2010 4:36 pm
Re: muffler shops, anyone have a good one that they use
airbur wrote:AA Performance Muffler & Brakes on Broadway in Littleton. These guys are awesome! I had them install duals. I supplied Hooker Competition Turbo mufflers but they can get anything you want. They had it done a couple hours after dropping it off.
http://local.yahoo.com/info-19565314-aa ... eton%2C+CO
I used these guys for mine. They did a great job, quickly.
650 from headers back including cat and muffler and chrome tip
1977 Sport, 351w OBDII EFI motor, 4R70W auto, 4:88 gears, ARB lockers, 3.5" suspension, 33" tires.
- kcfeist
- Official CCB Member

- Posts: 19
- Joined: Sat Feb 25, 2012 5:03 pm
Re: muffler shops, anyone have a good one that they use
airbur wrote:AA Performance Muffler & Brakes on Broadway in Littleton. These guys are awesome! I had them install duals. I supplied Hooker Competition Turbo mufflers but they can get anything you want. They had it done a couple hours after dropping it off.
http://local.yahoo.com/info-19565314-aa ... eton%2C+CO
Another vote for this place. I have not used them, but I went with a friend to get brakes and exhaust on his 83 f250. He is not real mechanical and wanted me to go to make shure he woulkdn't get ripped off. I was impressed by their proffesionalism and the price.
-
broncobuster
- Official CCB Member

- Posts: 3
- Joined: Thu May 03, 2012 9:04 am
Re: muffler shops, anyone have a good one that they use
The last time I had an exhaust put on was about 10 years ago so I can't speak for current pricing. I went to "Englewood muffler and radiator". I think was the name. I had used these guys for radiator work several times so I tried them for the exhaust. I had the headers and mufflers so they just needed to bend and run pipe for duals. Cost was $200. They are a small hole in the wall type of place but they do good work. They are on north Federal about 29st. Check the yellow pages and see if they are still around.
Terry
Terry
- Brianut
- Official CCB Member

- Posts: 350
- Joined: Thu Oct 14, 2010 6:06 am
Re: muffler shops, anyone have a good one that they use
I just got the exhaust done at AA Performance and will agree they do great work, really happy with how it looks and sounds, just have to burn off the oil residue. they threw on a "turbo" muffler.
Comparable to a Flowmaster in design and sound.
Comparable to a Flowmaster in design and sound.
- mdanko
- Official CCB Member

- Posts: 10
- Joined: Fri May 13, 2011 9:36 pm
Re: muffler shops, anyone have a good one that they use
I have had Scott at AA performance muffler install several exhaust systems for me. Great work and awesome performance.
- MOLLEY
- Official CCB Member

- Posts: 54
- Joined: Sat Dec 11, 2010 7:33 pm
Re: muffler shops, anyone have a good one that they use
there is a place in elizabeth that does great work and will do anything you want ,, forgot the name but only guy in town . glad you got set up
66 Bronco (Molley) injected 418 stroker on juice, klune v ,4 speed atlas hi 9 35 spline air lockers front & rear, rcv axles. 37'' red krawlers. Four other sets of tires for ice racing and dirt drags. 290lbs of welding wire.
- Boulderbronc
- Official CCB Member

- Posts: 40
- Joined: Thu Dec 23, 2010 10:28 pm
Re: muffler shops, anyone have a good one that they use
I got a guy here in Longmont, does it on the side in his house. He did duals on my 73 for $160 with mufflers!!
Headders back!!
Headders back!!