3 speed manual wont go into 2-3
-
socofn
- Official CCB Member
- Posts: 204
- Joined: Sat Apr 02, 2011 10:52 am
3 speed manual wont go into 2-3
Finally got everything back in and now it won't go into 2-3. It a 3speed on the collum and the linkage is free. I can move 1-reverse by hand but 2-3 wont budge and I do not want to put to much pressure on it. Suggestion are greatly apperciated. JP
74, MONEY EATER
-
akaFrankCastle
- Official CCB Member
- Posts: 4901
- Joined: Wed Oct 27, 2010 5:25 pm
3 speed manual wont go into 2-3
If your trans is toast, let me know. I have two organ donors in the garage you can pick apart.
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
-
Booger
- Official CCB Member
- Posts: 809
- Joined: Thu Dec 23, 2010 5:55 pm
Re: 3 speed manual wont go into 2-3
You just might have to take aka up on that offer.
Bob - Turning hydrocarbons into noise since 1970
Spiritual owner of the now Zoso mobile (1974 Bronco Ranger - EFI 351W-4R70W-ARB front and rear-STC softtop- High Country hood-3 1/2" WH lift- Cross inboard rear shock mnt- Duffs bumpers- Warn 8274- 33's- Cheby disc conversion)
Spiritual owner of the now Zoso mobile (1974 Bronco Ranger - EFI 351W-4R70W-ARB front and rear-STC softtop- High Country hood-3 1/2" WH lift- Cross inboard rear shock mnt- Duffs bumpers- Warn 8274- 33's- Cheby disc conversion)
-
socofn
- Official CCB Member
- Posts: 204
- Joined: Sat Apr 02, 2011 10:52 am
Re: 3 speed manual wont go into 2-3
I hope it isn't as it is the one I just got from airbur attached to a 302 that was working. I have not had time to mess with it since friday but if anyone has any ideas what I can do to figure this out, your input is greatly apperciated. Thanks JP
74, MONEY EATER
-
akaFrankCastle
- Official CCB Member
- Posts: 4901
- Joined: Wed Oct 27, 2010 5:25 pm
3 speed manual wont go into 2-3
Well, my first suggestion would have been to pull the top cover and have a look see at what is hanging up.
Just for giggles, you are manipulating the shift levers in a R-N-1/3-N-2 fashion, correct? Middle position being neutral, gears to either side.
Just for giggles, you are manipulating the shift levers in a R-N-1/3-N-2 fashion, correct? Middle position being neutral, gears to either side.
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
-
socofn
- Official CCB Member
- Posts: 204
- Joined: Sat Apr 02, 2011 10:52 am
Re: 3 speed manual wont go into 2-3
On the shift levers it goes freely into r-n-1 and will not move at all into 2-n-3. Pulling the top cover is going to be a PIA as it is already installed!!! I will do what I need to tho to get it back up and runnin. Thanks JP
74, MONEY EATER
-
airbur
- Official CCB Member
- Posts: 1721
- Joined: Wed Sep 29, 2010 7:39 am
3 speed manual wont go into 2-3
What did you do to my tranny?! I had no prob shifting it the day I took the video for you.....ran it around the city a bit to make sure everything was in good working order before I pulled it.
Maybe an issue with how the clutch linkage is setup?
Maybe an issue with how the clutch linkage is setup?
Sold: 1970 w/427W Injected Stroker
-
socofn
- Official CCB Member
- Posts: 204
- Joined: Sat Apr 02, 2011 10:52 am