Landsharks 76er Refresh and Build

[Viperwolf1]

The filter fitting unscrews and the explorer parts can swap right over.

[landshark]

The filter fitting unscrews and the explorer parts can swap right over.

is there really any added benefit of adding it in? i have the cooler all cleaned up and and painted ready to be installed.. but not sure there was a benefit for a street rig?

[Viperwolf1]

Hard to say. Ford put them on the explorers for a reason though.

[landshark]

so i can unscrew the oil stud that is in the block and install the cooler?

[Viperwolf1]

Yes. As long as you have the explorer hollow bolt and big and small o-rings. It's a tight fit between the cooler and the cross member. You might have to remove the drip rail from the cooler. You can also clock the cooler up a little by trimming the locating tab.

[landshark]

Yes. As long as you have the explorer hollow bolt and big and small o-rings. It's a tight fit between the cooler and the cross member. You might have to remove the drip rail from the cooler. You can also clock the cooler up a little by trimming the locating tab.

sounds like trouble ;)

[Rox Crusher]

The filter fitting unscrews and the explorer parts can swap right over.

is there really any added benefit of adding it in? i have the cooler all cleaned up and and painted ready to be installed.. but not sure there was a benefit for a street rig?

I was told that the 5.0 in an explorer, which is heavier than mustang and is more likely to be used harder such as towing, created more engine heat and that they couldn't make the oil pan any larger so they came up with the cooler.

In 99, they quit using it but that was also the year they went to a lower horse power / smaller (14lb) injector configuration

[Badlands]

Looking good Chris. You have gotten a lot done!
My fan sits inside my shroud a little too far and doesn't draw air properly. I'll have to see what you fab up and copy how you do it but with the right depth for me.

[landshark]

Thanks. I will probably make the shroud that's listed on the Ccb serp write up. Just need to go get the aluminum.

Got the wiper motor and mechanics installed. Also picked up my new to me wheels and tires.

[landshark]

Got the tail lights, sidemarker lights and all the rear wiring in.. so thats done.. i hope. I guess i need to order up some stuff from one of the vendors and get started on the dash so I can get that steering in.. and then brakes... etc etc etc

Decided to order my EFI harness tomorrow, get that ball rolling.. then it just leaves headers and a fuel tank... maybe next month ;)

dropped 2 of the 7" wide slots off yesterday to get fixed up... had a bit of road rash and one was out of round.. so having them fixed.. decided i would bite the bullet and polish them as they wanted way too much to polish... i know its going to take some time.. but hopefully they will shine up!

[landshark]

Not much going on, lots of little things, just ordered my EFI wireharness so thats something. As soon as I get my gauges back from the resto guy i will be ready to put the dash and steering wheel back in.. which will allow me to put the steering shaft, brakes and most of the wiring in and continue the build.

I guess i could get started polishing some wheels ;)

Oh got the firewall and under cowl area covering in...

[Rox Crusher]

I am thinking now would be a great time to ad a/c to your resto-mod


? ? ? ?

[dsmith01]

I am thinking now would be a great time to ad a/c to your resto-mod


? ? ? ?

x2 - wish I would have while the dash was out.

[landshark]

iam thinking $1500 is better spent elsewhere ;)

[landshark]

Got the grill back from the painter, started installing the FORD badge letters which i cleaned then painted with red enamel hobby paint.. polished them up a little, they dont look too bad for being 36 years old. Thats Argent Silver in the center of the grill by the way.







Also decided that I didn't like the location where the stock exploder intake was and rather then fiddling around with trying to make some weird connections I picked up a 3" aluminum tube with silicon joiners. I got a reducer for the MAF side to go from the 3.25" MAF connection down to 3". Now i just need the cone filter and the MAF conversion plate.. seen it on ebay but just have to get around to picking it up.

I will be cutting the tubing down to put the intake exactly where i want it on the wheel fender. I want to keep the stock overflow bottle and washer so this should work out well.




Picked up two of the slots I had fixed and realigned, they decided to do a quick polish one to see how it would look.. so 3 more to go! guess i know what I will be doing this weekend ;)





and got my spare wheel blasted and powder coated Argent silver to keep some of the originality with the truck...

[Flatheadpopup]

Wow, that wheel polished up nice! Sorry to hear that one of them was out of round...I never ran them and had no idea. You still gonna put the bfg's on them or did you decide to go bigger? Oh, it was nice meeting you by the way.

[landshark]

Wow, that wheel polished up nice! Sorry to hear that one of them was out of round...I never ran them and had no idea. You still gonna put the bfg's on them or did you decide to go bigger? Oh, it was nice meeting you by the way.

Oh no worries. I got all the curb rash fixed and the little bend straightened. Just turned out one of the wheels was out of round so had them fix it as well.

I will be running the bfg s hopefully have them mounted this weekend or by we'd. Once I can actually drive it i will see if I want to go bigger

[landshark]

Got a bit more done this weekend.. lots of little stuff mainly..

Ran half of the charging system wires and started to run the headlight wiring..



Also got the intake cut and mounted.. just need to get the MAF adapter and cone filter, also need to cut a hole for the ACT sensor - forgot to do that..

I will need to fab up a little mount for the end of the air intake as I think it wont be happy in there and eventually start moving.. but right now its pretty solid.



Cut the top of the PS bracket and ran the upper radiator hose through it along with the high Pressure PS hose. I will be sleeving the radiator hose sooner or later.. just in case.

Also installed the plug wire holders.. had to drill them out a bit to get the bolts to fit right. there are a few spots where they are a little close to stuff.. but I will sleeve some of the wired in case they rub.. stuff is already getting tight!





Installed the steering column, shift lever and the supports. I should be able to get the dash in with it installed, i really wanted to move along with the engine bay stuff. Also got the heater in place.. gives me a good look at where i can mount the computer...







I haven't installed all the ground wires yet, but did install a ground strap from the back of one of the heads to the firewall. I scuffed the firewall across the washer to try and get a good ground connection. Next I will runa ground wire directly to the engine from the battery then the frame and then frame to engine bay body.



Next up is to get the aluminum shroud extension made, hook up the transmission lines and figure out why my steering shaft isn't fitting onto the splines..

[Justin]

Looking good! You've made great progress.

[D&D72]

That thing is looking damned SEXY!

[landshark]

Got the fan shroud extension made and installed. I Think the lower radiator hose will work fine but its going to need some plastic covering and a Holder to keep it in place and from rubbing...



yes.. i need to get the scratches out of the alumunum







harness wont be here until monday :(

but I'm sure I can figure out other stuff to do ;)

[Booger]

Looking good Chris. Can't wait to see it on the road.

[hockeydad4-22]

Chris, I have your windshield cut and resting safe and sound in my garage. Been rather busy (I am sure you understand). I will look at the schedule and let you know what afternoon this week I can come over and install it.

[landshark]

Chris, I have your windshield cut and resting safe and sound in my garage. Been rather busy (I am sure you understand). I will look at the schedule and let you know what afternoon this week I can come over and install it.

sounds good. i will be here all week just give me a heads up

[landshark]

something showed up!



a couple more pics of progress...

[ZOSO]

Is that just the efi harness or a full kit. I've been really eyeing those.

[Gunnibronco]

Wow, that is awesome. So shiny!

[landshark]

Is that just the efi harness or a full kit. I've been really eyeing those.

just the efi harness.. haven't had a chance to really go through it.. just opened it.. but has a few re-wired bits and explorer ends.

This is the RJM harness.. Ryan licensed it out - guy i delt with is very responsive and knowledgable

[landshark]

Started rewiring stuff and populating the dash.

[hockeydad4-22]

Drug the "tub-o-wires" out of the basement last night. Started rooting through for your brake light and decided to just let you do your own digging - like a treasure hunt of sorts.

I plan to be at your place around 6pm or so, with the windshield and the previously mentioned "tub-o-wires". If that still works for you.