Rear seat belt question
-
akaFrankCastle
- Official CCB Member
- Posts: 4901
- Joined: Wed Oct 27, 2010 5:25 pm
Rear seat belt question
I'd planned to go to the yard today and hunt for a set of good used seat belts to put in the back of the Bronco. Was thinking I would pull lap belts from a 70's truck. Wanted to know what the bolt size is on the Bronco rear belts, or if it is a Torx type head. Want to pack in minimal tools, get in and out quick. So, anyone happen to know the bolt size? Danke.
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
-
Jesus_man
- Official CCB Member
- Posts: 5988
- Joined: Thu Nov 11, 2010 9:36 am
Re: Rear seat belt question
1/2" to 5/8" would be my guess but it's been a while since I've messed with mine. - Bitte!
1973 Bronco, 351 SEFI, Locked, discs, 35's ZF-5spd and Atlas 4spd. 235:1 Crawl Ratio. It may be ugly, but it's slow.
http://www.ucora.org
http://www.ucora.org
-
sbolt19
- Official CCB Member
- Posts: 740
- Joined: Wed Oct 06, 2010 9:04 am
Re: Rear seat belt question
Take the bolts. They are torx & they will fit the back end.
-
akaFrankCastle
- Official CCB Member
- Posts: 4901
- Joined: Wed Oct 27, 2010 5:25 pm
Re: Rear seat belt question
Definitely going to need the bolts. All of my hardware is gone. PO stripped the entire backseat and belts out of the truck. Before bolting down a sheet of 1/2 plywood in the back.
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
-
cracker
- Official CCB Member
- Posts: 113
- Joined: Mon Oct 04, 2010 8:19 am
Re: Rear seat belt question
Look for seatbelts from an early 4runner, the rears work GREAT for EB rears. Long and adjustable!
1-1966 Bronco
1-1967 Bronco
1-1969 Bronco
2-1973 Broncos
And a couple even run.....
1-1967 Bronco
1-1969 Bronco
2-1973 Broncos
And a couple even run.....