1/2 Cab Hard Top Bikini

[mickphatmac]

Whatever you want to call it!??

Started life as a full hard top...

Cut in half to make a home made 1/2 cab...

Then morphed into this.
It's in good shape Rust wise. Still needs some bondo/body work at the overlap. You will have to make brackets for the back where it attaches to your roll bar, or whatever you decide to mount it to.

Looking for $100 obo.

[mickphatmac]

I have the Chevy spindles and Chevy backing plates...
I would TRADE (the TOP) for some Ford Hub/Rotor assemblys and calipers if you're interested in that?

[colby45]

This is sort of off topic, but what brand and size tires are those? I really like the look of them.

[Broncobsession]

Looks like bf Goodrich km2's, maybe 33x10.5x15-ish. Looks great.

[mickphatmac]

Thanks!
235/85-16 (32's)
BFG KM2's

[colby45]

Awesome thanks for the info!

[mickphatmac]

If ANYONE is interested in this I'd be willing to entertain offers or trades???

Just want it out of my way ;)

(not looking for anything in particular, what do you have?)

[mickphatmac]

This was my inspiration! HA!!!!

[sykanr0ng]

I have a blue one of those, I like the idea too.

Not sure I have anything to trade that you'd want, and money is a little low for a while.

[mickphatmac]

I don't have anything specific in mind....

I do need front fenders, cut or uncut.
Fender flares. Rear for sure.
Right and Left window gaskets for a Top.
I need my hard top body worked and painted.

I don't know, something worth $100-$150.
Beats Me!?!?

[mickphatmac]

C'mon...$100 Bucks!!!

[Dirtheadz]

Do you have a measurement from the windshield - back? I need to see how much this actually covers

[mickphatmac]

From the center of the front bolt holes for the windshield, to the middle of where I bolted it to my rollbar is 37 inches .

The total from the very front lip to the Back lip of the half cab is almost 41 inches.

I think every bronco is going to have a different set up for this top because every rollbar will sit just a little bit different.

No matter what you have I think you're going to have to make a couple of brackets that go from the rollbar to the back of the top, that's just the way it is.

Mine was set up where it is cut out in the back so the rollbar fit right in the middle of that cut out. The top just slid down onto the top of the rollbar, and you'll see where the two bolts were that went through the rollbar and into the back of the cab top.

Just eyeballing it from some of my old pictures on the driver side I would say the back lip goes back to exactly right in front of the front gas cap, if that helps?

Had to explain but easy to imagine if you're looking at it .

[Woodscaper]

Do you still have the soft top? Will you be coming to the swap meet/breakfast?

[mickphatmac]

I do have it...
It will be the Soft top only, No Hardware though. I just bought a White K-Line soft top from Michigan!

I can't come to the Breakfast. We have 2 boys in Travel Baseball. I'm off next Wed and off at noon-ish next Thurs. We could meet somewhere?

[Woodscaper]

I do have it...
It will be the Soft top only, No Hardware though. I just bought a White K-Line soft top from Michigan!

I can't come to the Breakfast. We have 2 boys in Travel Baseball. I'm off next Wed and off at noon-ish next Thurs. We could meet somewhere?

Thanks, I dont need the top if it does not have the hardware and stuff to install it.

[mickphatmac]

Ladies!!! Lets take your TOPS OFF!!!

$100 BUCKS!