I am looking to convert my Bronco back to a Manual Trans and need the Following Parts:
-Intermediate shaft that goes from manual trans to Dana 20 T
-Complete Clutch Linkage except Pedal
-Steering Column ?
trying to get parts for a winter project
Any help appreciated thanks GMAN
DANA 20 intermediate Shaft for a Manual trans
-
GMAN
- Official CCB Member
- Posts: 37
- Joined: Mon Dec 06, 2010 8:31 am
DANA 20 intermediate Shaft for a Manual trans
GMAN
70 Roadster 347 burnt orange
70 Roadster 347 burnt orange
-
akaFrankCastle
- Official CCB Member
- Posts: 4901
- Joined: Wed Oct 27, 2010 5:25 pm
Re: DANA 20 intermediate Shaft for a Manual trans
Where are you located?
Stroppe'd
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
1972 Sport, 302, 3 speed with old school Duff floor shifter, T shift Dana 20 with JB Fab twin stick, 4.11 gears with Trac-loc, Lincoln hydroboost, Chevy disc conversion, WH gas lift gate shock kit, 33" Duratrac tires on slots and about 2.5" of lift, Stroppe installed: bumper braces, dual shocks on all four corners, GM power steering, trans cooler mount, auto shift column, rollbar.
The Terrible One
1972 Sport uncut, 302, C4 with 1974 column , T shift Dana 20, 3.50 gears w/ limited slip, 1966 U13 Roadster kick panel, and factory power steering.
1973 Stroppe Baja project
-
DanHall
- Official CCB Member
- Posts: 151
- Joined: Fri Jan 17, 2014 1:38 pm
Re: DANA 20 intermediate Shaft for a Manual trans
I have the input shaft for the D20 and most of the clutch parts including the bellhousing. I'm swapping to a auto. Heck, I think I even have a new bearing for the input shaft that came with the rebuild kit.
-
GMAN
- Official CCB Member
- Posts: 37
- Joined: Mon Dec 06, 2010 8:31 am
Re: DANA 20 intermediate Shaft for a Manual trans
I'd be interested in the parts sorry fro the late reply I've been out of town
GMAN
70 Roadster 347 burnt orange
70 Roadster 347 burnt orange
-
DanHall
- Official CCB Member
- Posts: 151
- Joined: Fri Jan 17, 2014 1:38 pm
Re: DANA 20 intermediate Shaft for a Manual trans
I'm down in Pueblo, out East of town near the airport. I'll PM you a number and we can work out a time.
-
Justin
- Official CCB Member
- Posts: 6199
- Joined: Sat Oct 09, 2010 11:04 pm
Re: DANA 20 intermediate Shaft for a Manual trans
GMAN, not sure where you're located, but I get down to Pueblo semi-regularly and can shuttle the parts north to Denver in a few weeks.