Hi Gang,
I was hoping you could help identify where this sound is coming from... it's not in my Bronco but rather my pickup truck -a 69' Dodge.
It's coming from under the truck and usually only happens when I take my foot off the clutch or gas pedal. As soon as I put my on the clutch pedal, it goes away. Oddly, it sometimes it happens when I hit the gas pedal too. Doesn't matter which gear I'm in. It does get louder when turning right.
The clutch is new (I've put maybe 3000 miles on it), the carb is rebuilt, new points, distributor, cap, rotor, spark plugs, alternator, voltage regulator, etc. Also just recently had green bearings put in the rear end with brand new brake drums, pads, hoses, master and wheel cylinder, etc on the brake system. Pretty much everything is new there....
Here's a video/audio clip: http://vid98.photobucket.com/albums/l27 ... ikf060.mp4
Any insight would be appreciated.
Thanks,
Danny
Odd Sound Question
- Moab Mike
- Official CCB Member

- Posts: 1945
- Joined: Mon Jan 03, 2011 1:59 pm
Re: Odd Sound Question
When you replaced the clutch did you replace the throw out bearing?
-
dcombs
- Official CCB Member

- Posts: 69
- Joined: Wed Feb 18, 2015 6:06 pm
Re: Odd Sound Question
Yes.
I should mention I checked the u-joints and they seem fine. No movement at all. BUT my driveshaft center bearing has some play. Could that be making the sound?
Thanks,
Danny
I should mention I checked the u-joints and they seem fine. No movement at all. BUT my driveshaft center bearing has some play. Could that be making the sound?
Thanks,
Danny
- Moab Mike
- Official CCB Member

- Posts: 1945
- Joined: Mon Jan 03, 2011 1:59 pm
Re: Odd Sound Question
your center bearing should have no play at all.
-
dcombs
- Official CCB Member

- Posts: 69
- Joined: Wed Feb 18, 2015 6:06 pm
Re: Odd Sound Question
Thanks, Mike. It has quite a bit of play so I'm thinking that's what it is. Does the sound like that to you?
I've never changed one before - can I do it without a hydraulic press?
Thanks,
Danny
I've never changed one before - can I do it without a hydraulic press?
Thanks,
Danny
- ZOSO
- Moderator

- Posts: 3910
- Joined: Mon Nov 15, 2010 4:58 pm
Re: Odd Sound Question
did you replace the pilot bearing/bushing?
Rob
74 Ranger EFI351w, 4r70w, ARB 5.13 9in, ARB 5.13D44, and a bunch of other goodies. Best of all the family memories.
04 Mustang Cobra, KenneBell 2.2 feeding a lot of boost on E85. Tire shredding machine
New project: 77 Bronco Ranger, body work and more body work.
Very little left of a 72 durango tan explorer sport
74 Ranger EFI351w, 4r70w, ARB 5.13 9in, ARB 5.13D44, and a bunch of other goodies. Best of all the family memories.
04 Mustang Cobra, KenneBell 2.2 feeding a lot of boost on E85. Tire shredding machine
New project: 77 Bronco Ranger, body work and more body work.
Very little left of a 72 durango tan explorer sport
-
dcombs
- Official CCB Member

- Posts: 69
- Joined: Wed Feb 18, 2015 6:06 pm
Re: Odd Sound Question
Zoso, yes. That was my thought too at first. I guess it's possible the new one went bad... I sure hope not. Did it sound like the pilot bearing to you?
Thanks,
Danny
Thanks,
Danny
- ZOSO
- Moderator

- Posts: 3910
- Joined: Mon Nov 15, 2010 4:58 pm
Re: Odd Sound Question
My car had a new pilot bearing failure that sounded very similar.
Rob
74 Ranger EFI351w, 4r70w, ARB 5.13 9in, ARB 5.13D44, and a bunch of other goodies. Best of all the family memories.
04 Mustang Cobra, KenneBell 2.2 feeding a lot of boost on E85. Tire shredding machine
New project: 77 Bronco Ranger, body work and more body work.
Very little left of a 72 durango tan explorer sport
74 Ranger EFI351w, 4r70w, ARB 5.13 9in, ARB 5.13D44, and a bunch of other goodies. Best of all the family memories.
04 Mustang Cobra, KenneBell 2.2 feeding a lot of boost on E85. Tire shredding machine
New project: 77 Bronco Ranger, body work and more body work.
Very little left of a 72 durango tan explorer sport