A bunch of Dana44 Axle Shafts - Various lengths

Post by **landshark** » Sun Feb 14, 2016 8:59 pm

I have a few different axle shafts from several different Dana 44 equipped trucks. I don't remember exactly where they are from but know one set is probably from full width F150 or F250, probably 74-77. I can take measurements if needed, tried to provide some in the pictures below. Willing to take what you think they are worth - let me know.

Post by **Kinder** » Mon Feb 15, 2016 8:43 am

Can you put together a bronco set from all your pieces? I don't have the measurement off the top of my head, but Zac needed a complete set.

Post by **landshark** » Mon Feb 15, 2016 9:43 am

kinder wrote:Can you put together a bronco set from all your pieces? I don't have the measurement off the top of my head, but Zac needed a complete set.

I dont know if any of these will fit an EB, the outers maybe...

i will look for measurements

Post by **Kinder** » Mon Feb 15, 2016 10:23 am

I've got a trail spare set, I'll dig them out & measure as well.

Post by **landshark** » Mon Feb 15, 2016 12:32 pm

I do too. Just remembered. Will take measurements tonight and let you know.

Post by **landshark** » Mon Feb 15, 2016 9:56 pm

Pulled out my backup front axle shafts and took some measurements.

Looks like these four outers are the same size

But the short side inners are not - one is 1/4" longer the other about 1" longer.

EB Inner length is 16.5"

One is 16.75"

two are 17"

The long side inner is way too long, not even close to a EB axle.

Don't know if that was helpful. one set of driver side might work. three of outers look to be a match.

let me know would love to get these out of my garage or i might turn them into art.

Post by **Justin** » Tue Feb 16, 2016 8:46 am

Outers should be the same between the EB and F150/Bronco axles (9 23/32" long as measured from the end of the axle to the center of the u-joint cap). Do you have any inners that are 18 29/32" and 33 29/32"? If so I'll take a full set. Otherwise I'll take one of the outers. I'm assuming the shiny aftermarket stuff in the pic is your spare?

Post by **Kinder** » Tue Feb 16, 2016 12:07 pm

Set aside a couple of outers and the one inner that is close for Zac, I'll work on meeting up.

Post by **landshark** » Tue Feb 16, 2016 3:44 pm

kinder wrote:Set aside a couple of outers and the one inner that is close for Zac, I'll work on meeting up.

Ok

Post by **landshark** » Tue Feb 16, 2016 3:52 pm

Justin wrote:Outers should be the same between the EB and F150/Bronco axles (9 23/32" long as measured from the end of the axle to the center of the u-joint cap). Do you have any inners that are 18 29/32" and 33 29/32"? If so I'll take a full set. Otherwise I'll take one of the outers. I'm assuming the shiny aftermarket stuff in the pic is your spare?

One set inner 34 29/32 with outer at 10 3/4 or so
One set inner is 18 29/32 outer is 9 23/32
One set inner about 19 outer is 9 23/32
One inner at 18 29/32
Two outer at 9 23/32

I think those are correct. So looks like I can accommodate some of what you and Kirk want.

www.ColoradoClassicBroncos.com