June Breakfast and Swap Meet

[D&D72]

I need a solid. Scott is bringing my portable welder setup (it's the small one he had for sale) with him to the breakfast. Can a local dude grab it from him for me? Rox might be able to do it if he is able to attend, but I need a backup if he's unable to grab it.

I can get it if no one closer to you can.

I could as well.

[Gregg]

I'm going. I'm bringing odds and ends in the van. I'll bring this roll bar (minus hi lift mounts) if someone is interested.

How many bolt holes in the B pillar feet?

3 holes in every foot bottom. The front feet have side panels with 2 holes in each.

[mickphatmac]

I'm going. I'm bringing odds and ends in the van. I'll bring this roll bar (minus hi lift mounts) if someone is interested.

I'm not going to make it to the breakfast, any chance someone on the North end could pick this up for me?

[Kinder]

Thanks Justin & D&D72

[ScottBarnes]

Thanks Justin & D&D72

I'll be in the Stroppe, so I should be easy to find!

[Dirtheadz]

sorry guys... not making it

[rt9]

I need a solid. Scott is bringing my portable welder setup (it's the small one he had for sale) with him to the breakfast. Can a local dude grab it from him for me? Rox might be able to do it if he is able to attend, but I need a backup if he's unable to grab it.

I'm going to make it after all. I can grab it and drop it off at your house or you can come by the office or house. 720-838-5980 c

Rick

Sent from my SM-P600 using Tapatalk

[plumbdoctor]

I am bringing

Mustang get 40's the smaller chamber f3's
Lincoln rear disk set up minus hoses and rotors
Washer fluid containers
A couple of boosters and mc's ( no brackets)

Also if anyone is interested... A viper built c4,
C4 core

And what ever else that will fit in the Broncos

[Kinder]

I'm going to make it after all. I can grab it and drop it off at your house or you can come by the office or house. 720-838-5980 c

Rick

Sent from my SM-P600 using Tapatalk

That'd be awesome, thanks!

[Moab Mike]

Looks like I'll make this one. I'll bring a load of cash, 3 full storage units just isn't enough for me.

[landshark]

It looks like I will make this one will be bringing stock odds and ends.

3.5 wild horses coils.
3.5 inch duff leaf pack with less than 1000 miles on them.

And more.

Are we brining scrap as well?

[Rox Crusher]

I'm going to arrive early but have to leave by 9:30.

I will bring a bunch of miscellaneous knick knack stuff I want to be relieved of

[phyler]

I'll have the following:

351w Truck EFI (upper/lower intake, throttle body, etc.)
351w Heads from a 96 F250 (E7's I believe but haven't looked)
Exhaust manifolds from the same F250
3G Alternator
351w front-dress items
BW1356 Transfer case including the shifter
Stock Clutch rod for a Bronco
Set of outer rocker panels (used)

I won't have it ready but if anyone wants a short block 5.0, let me know. I am pulling the Explorer front-dress and the GT40 heads. Will have the block and the lower intake from it avail shortly but probably not in time for tomorrow.

[plumbdoctor]

It looks like I will make this one will be bringing stock odds and ends.

3.5 wild horses coils.
3.5 inch duff leaf pack with less than 1000


Chris are the rears 11 pack?

Either way I need em....

[landshark]

Need one maybe two new bushings. Other than that they look new

[plumbdoctor]

Perfect,

[samst145]

Was great getting out and meeting some of yinz! Got some great advice, Bronco heading to the Carb Shop tomorrow for a tune, then heading to see Mike for a week or two :) Can't wait to meet up on some trails!

[plumbdoctor]

Yinz, Yinzers and 'nat...samst145 , we were just back for game 5 of the cup...man I miss that place

[Eck]

Did you guys do a scrap run? I have some stuff I would love to get out of my way if there is another one planned later this summer...

[Justin]

Did you guys do a scrap run? I have some stuff I would love to get out of my way if there is another one planned later this summer...

No scrap runs planned at this time. Scrap prices are to low to make it worthwhile.