Rox Crusher's 77 sport

[Gnsteam]

Hi Jeff,

I hear yea about needing to win the lottery. My DecorΓÇÖs paint is pretty ruff, at least the rig has very minimal rust issues. There will be many safety, mechanical and comfort upgrade before it receives new paint.

Looking forward to seeing your winch project. I was inspired to do a hinden winch when I seen xcntrkΓÇÖs winch build at CB.com.

Thanks for the update,

Fred

[Rox Crusher]

In preparation for Super Cell West, I am finally getting around to doing this project.

Here is what IΓÇÖm working with;
- 1-3/8ΓÇ¥ body lift (minimum requirement for 351w with Ford OBDII EFI and stock hood)
- Explorer radiator which hangs slightly lower than Bronco radiator
- Warn M8 series winch with synthetic rope
- Badlands winch mounting plate

First thing was to locate and clean up my old frame horn inserts I used with the Meyers plow.

95B7CF95-98F2-4320-8E83-A6AF0FF685B0.jpeg

F78303EA-2BA7-43F3-BDF2-F4F5A9268F2B.jpeg

0E801A24-51F4-4E9B-9D49-50101314CDD6.jpeg

[Kinder]

IΓÇÖm interested in how this turns out, IΓÇÖd like to do something similar on TFB.

[Rox Crusher]

IΓÇÖm interested in how this turns out, IΓÇÖd like to do something similar on TFB.

IΓÇÖm wrestling with placement. Considering raising the radiator so the winch plate can be mounted to the bottom of the frame.

Right now the winch is up against the bottom of the radiator and the bottom of the grill.

I need about 5/8ΓÇ¥ which is achievable with radiator but not sure if raising the radiator will allow me to move winch back enough to clear the grill. DonΓÇÖt want to cut grill.

[Viperwolf1]

Body lift.

[Gunnibronco]

Body lift.

[Jesus_man]

Nose job?

[Digger]

Body lift.

If only Ford had the foresight to anticipate EFI and diesel swaps, overdrive transmissions, winches, dual batteries etc, when they designed the body structure we could have avoided all these unnecessary body lifts.

[Rox Crusher]

Body lift.

Cutting the grill sounds more reasonable.

:)

[mickphatmac]

Body lift.

Cutting the grill sounds more reasonable.

:)

[BroncoRaider]

https://www.dufftuff.com/Early_Bronco_R ... 4175-6.htm

Body lift and this?

[landshark]

mount the winch behind the rear axle and run the cable to the front and mount the fairlead on the stock bumper.

[Jesus_man]

[Rox Crusher]

https://www.dufftuff.com/Early_Bronco_Rolled_Filler_Panels_p/4175-6.htm

Body lift and this?

Yup

[Rox Crusher]

Finally got some time to work on it again.

This is the best itΓÇÖs gonna fit unless I want to move the radiator up and / or back.

Ended up with 3/8ΓÇ¥ flat bar as shim between bottom of frame and the winch mount.

So now I just need to figure which way I want to mount the bumper.

DonΓÇÖt worry that cheep ass grade 1.7 carriage bolt is just there for mocking it up.

15FF5DB7-1E6C-4ED7-887C-474E78831983.jpeg

023F07A5-D380-471C-A008-7024E700AD7A.jpeg

[mickphatmac]

so you don't want a 1" body lift...but it will look like you're running one...

Well played ;)

[Rox Crusher]

so you don't want a 1" body lift...but it will look like you're running one...

Well played ;)

I ended up having to put 1-3/8" body lift in when I went to 351W efi

I am pretty sure will mount the stock bumper on top of frame like normal and have the bottom part of the winch mount showing.

Nice thing is that the winch is fully behind the frame so the bumper won't have to be mounted forward of stock location.

[Rox Crusher]

More progress today........

Lots of fitting and refitting. Bumper is mounted in stock position.

I removed the ends of the winch plate which were protruding outside of the frame rails.

Extra points for anyone that can point out the obvious problem.

E3C9B666-655A-48DB-B91C-65935D96BF2F.jpeg

B3AEB73F-EBEA-4744-AC7F-59DA71DC72B2.jpeg

EC542F7B-A3EE-4FA0-AD0E-95EE1D7D4A28.jpeg

8A2614E6-B760-4347-B8EA-9B97EFB40311.jpeg

D2B5B624-7C1A-4A0E-94E5-93970B39D009.jpeg

[Eck]

So where does the rope come out?


Sent from my iPhone using Tapatalk

[BroncoRaider]

Plenty of room for the rope to come out of that HUGE gap between the grille and bumper.

[Eck]

Plenty of room for the rope to come out of that HUGE gap between the grille and bumper.

Might have to flip the fairlead plate to the top.


Sent from my iPhone using Tapatalk

[Rox Crusher]

Plenty of room for the rope to come out of that HUGE gap between the grille and bumper.

I think that gap is gonna come in handy for the clutch release lever.

I am gonna re-clock the clutch housing one notch and modify the release handle so I can access it through the gap.

Still gonna do the fillers at some point though.

[Rox Crusher]

So where does the rope come out?


Sent from my iPhone using Tapatalk

ThatΓÇÖs the dilemma......trying to decide what fairlead to use and how to mount it. Also have a cool flip up license plate holder IΓÇÖm trying to think of how to use.

[Strike2]

That turned out great, nice work looks awesome!

[Jesus_man]

Well done! A nice polished hawse fairlead would look right at home there. But incorporating a flip up plate holder would be cool. My advice is to keep the bottom of the plate higher than the bottom of the bumper. I bent mine enough that it broke off.

[mickphatmac]

That's TOTALLY BAD ASS Rox!
I would do that in a heartbeat if I had any Mechanicabilityness about me...but I don't so?
Anyway Nice job!!! Love it!

[Rox Crusher]

That's TOTALLY BAD ASS Rox!
I would do that in a heartbeat if I had any Mechanicabilityness about me...but I don't so?
Anyway Nice job!!! Love it!

thanks.....

If only I could achieve a gap similar to the one on your picture

[Rox Crusher]

A little more progress...........

I didnΓÇÖt quite get the opening for the fair lead in the perfect spot in the bumper so there is little crown to bumper when tightened down. Good enough for now.

As you can see IΓÇÖm using the new tangle free rope.

Also, still trying to figure out a slick solution for the clutch release lever. I cut the lever part of it off for now and it sits right behind the bumper. May drill an access hole large enough for a screw driver or Allen wrench and modify lever to suit.

B6B04550-E270-4F5D-BAD1-E0BAEABCDE67.jpeg

36914B2E-A5C9-446D-AAD2-87CBB8B2883F.jpeg

[Strike2]

That turned out really nice, I like how hidden the winch is and drilling a small hole for the release lever seems like the only option. If you do use a small screwdriver or Allen wrench to activated is there enough room to cap the actual winch hole to keep junk out while not in use

[Rox Crusher]

The last couple of weeks have been hectic, canΓÇÖt decide if itΓÇÖs been a whirlwind or a tailspin?

My new job has had me super busy so I havenΓÇÖt had time to prepare my rig for Super Celebration. So I decided to bring it to a shop to have them install the Duff long arms and fix the leaking rear ARB locker, and a bunch of other stuff. I had a really bad experience with the shop such that I couldnΓÇÖt trust them to work on it anymore, so I had to get in the garage and do it myself.........which is the way I prefer it anyway.

The shop did a good job installing the long arms. Too bad they did a hack job removing the original radius arm mounts.

I installed Duff extended shock towers and their new MS2020 Eibach shocks.
I built a custom tow hitch with receiver going through stock bumper.
I installed Duff rocker guards.
I installed a new air tank and re-plumbed all the ARB lines front and rear.

Now I gotta pack for our adventure at Super Celebration West in Buena Vista.

CanΓÇÖt wait to go wheeling !