June Breakfast and Swap Meet

[Justin]

It's swap meet time! We'll go back to an old haunt with an ideal parking lot. Bring out all your old, random parts so that you can take home someone else's old, random parts instead!

When: 6/18/16 @ 0900.
Where: Golden Corral-3677 S Santa Fe Dr, Sheridan, CO 80110
How: In whatever vehicle carries the most old junk.
Why: Because you know you need more Bronco parts.

This is one of the better attended events each year, so it's also a great chance to catch up and lay eyes on a bunch of nice EB's. Hope to see everyone there!

[Dirtheadz]

Anyone doing a scrap run as well this year?

[Justin]

I hadn't been planning on it, as steel prices suck, but we could if there is enough interest.

[phyler]

Justin, it's the 18th right? Or are we doing this on a Friday?

Sent from my HTC One using Tapatalk

[Justin]

Yes, I screwed up the date. It's the 18th.

[cravenbronco]

Does anyone need a D20 transfer case ? I have a extra one that I could bring to the swap meet.

[Moab Mike]

Does anyone need a D20 transfer case ? I have a extra one that I could bring to the swap meet.

T or J?

[hockeydad4-22]

Does anyone need a D20 transfer case ? I have a extra one that I could bring to the swap meet.

T or J?

Regardless - bring it, someone may not know they want/need it until they see it

[Kinder]

I know Phil is always looking for good cores, if no one else wants it.

[plumbdoctor]

I could use the T-case

[cravenbronco]

I could use the T-case

Cool I'll bring it down

[Woodscaper]

I will be there and will have plenty of parts to trade or sell or give away!!!!

[phyler]

Is it too soon to start posting what we have to bring?

Sent from my Venue 8 7840 using Tapatalk

[tacobronco]

Nope, not too early to post what we have...

I still have a pair of stock axle assemblies that I'd like to get out of the garage... Someone was interested in one of them last year (can't remember who), but it fell through. Here goes again:

Anyone have any interest in a Dana 30 front end and/or small bearing 9 inch rear? Both are 3.50, the rear is tagged as a stock limited slip, but I've never cracked it open. Rear is complete drum-to-drum, front is knuckle-to-knuckle (no brakes, though I can probably scrounge up some drum brake spindles to go with it, if needed), and could use a new seal (passenger side axleshaft).

I know these aren't exactly sought after items, so wasn't planning on lugging them down there unless someone is interested in them.

[Digger]

Gauging interest:

Posting for a friend
'83 351W, ran when pulled, E3AE-6015-BA, $200

IMG_20160610_074559462_HDR.jpg

Full width Lincoln disc 9-inch, complete

IMG_20160611_101517865_HDR.jpg

I also have a nearly new (5K miles) BroncoGraveyard Dual-diaphragm brake booster, bracket and hardware
$100

[Justin]

What's the WMS to WMS on that axle?

[pgilbeau]

Gauging interest:

Full width Lincoln disc 9-inch, complete

Price on the 9"?

[Gunnibronco]

Curious about lug pattern & parking brake on that axle.

[pgilbeau]

Here is what I have to bring:

Tom's or BC Broncos brake booster
Gray STC top, canvas is good but missing some brackets/hardware
Old James Duff door inserts
1977 F150 radius arms, coils, and buckets
Everything for Explorer front dress except timing cover, water pump pulley, and fan

Also have some stuff for 93-97 Ford Ranger if anyone needs
Flexilite electric fan, P/N 40, have thought about seeing if I could adapt to the Bronco
3" Body lift
4.0 water pump, new
JET performance 180 degree thermostat, new

[mickphatmac]

I also have a nearly new (5K miles) BroncoGraveyard Dual-diaphragm brake booster, bracket and hardware
$100

I think I need that!
But I can't make it that weekend.

[phyler]

I also have a nearly new (5K miles) BroncoGraveyard Dual-diaphragm brake booster, bracket and hardware
$100

I think I need that!
But I can't make it that weekend.

If you take care of payment, I can get it to my place for you.

Sent from my HTC One using Tapatalk

[Digger]

I also have a nearly new (5K miles) BroncoGraveyard Dual-diaphragm brake booster, bracket and hardware
$100

I think I need that!
But I can't make it that weekend.

No problem. I work near I25 and hwy119 if you want to meet during the week, otherwise we can make arrangements.

[Digger]

Gauging interest:

Full width Lincoln disc 9-inch, complete

Price on the 9"?

$150

No idea about lug pattern or parking brake, but told it came out of a Lincoln. I don't have access to the the axle to look as I'm posting for a friend.

[pgilbeau]

Gauging interest:

Full width Lincoln disc 9-inch, complete

Price on the 9"?

$150

No idea about lug pattern or parking brake, but told it came out of a Lincoln. I don't have access to the the axle to look as I'm posting for a friend.

Interested depending on lug pattern, etc.

[Gregg]

I'm going. I'm bringing odds and ends in the van. I'll bring this roll bar (minus hi lift mounts) if someone is interested.

[mickphatmac]

Interested...
How much are you asking for the rollbar?

[cravenbronco]

I'm not going to be able to make it do to honey do's

[Kinder]

I need a solid. Scott is bringing my portable welder setup (it's the small one he had for sale) with him to the breakfast. Can a local dude grab it from him for me? Rox might be able to do it if he is able to attend, but I need a backup if he's unable to grab it.

[akaFrankCastle]

I'm going. I'm bringing odds and ends in the van. I'll bring this roll bar (minus hi lift mounts) if someone is interested.

How many bolt holes in the B pillar feet?

[Justin]

I need a solid. Scott is bringing my portable welder setup (it's the small one he had for sale) with him to the breakfast. Can a local dude grab it from him for me? Rox might be able to do it if he is able to attend, but I need a backup if he's unable to grab it.

I can get it if no one closer to you can.